0 comments / Posted by Trifox Team

1. Frame
To clean the frame, you can use a rag dipped in water to pour on the parts, so that the mud stuck to the bottom of the frame will easily become soft when exposed to water. At this time, just wipe with a rag to easily remove the mud. It is not advisable to use a high-pressure water gun to wash the sludge on the bicycle, because this cleaning will easily enter the bottom bracket or hub and affect the life of the parts.

At this time, you need to pay attention to some places where mud is easy to accumulate on the frame, such as the position of the bottom bracket on the bottom bracket. After washing off the muddy water on the frame with clean water, wipe it with a semi-dry damp cloth. When there is dirt on the frame, just wipe it back and forth several times, and the frame will be clean. Remember not to scrub with detergent and soapy water.
Trifox Carbon Fiber Hardtail MTB Frame MFM200
2. Wheels, front and seat tube

When washing the wheel set, you can choose to use the shoe brush dipped in detergent to brush the sand on the tire. When washing the rim, it is best to use a semi-dry damp cloth and carefully wipe the brake pads on the rim. Simply scrub the spokes. After washing the hub, do not use a high-pressure water gun to remove the detergent. Simply dip it in water and wipe it with a clean cloth. When washing the seat tube and the seat bag, be careful not to let muddy water flow into the seat tube along the seam of the seat tube clamp. Under the seat bag, it is often the place where mud and water fly up the most, so you must carefully wipe off the mud with a rag.

For tires, you can use a slightly harder brush to remove the sand and dust from the tires for simple maintenance.

3. Finger dial, forward dial, back dial

After washing the above accessories, the next step is to wash the fingers. The fingers are more complicated. There is more butter in the parts for lubrication. When cleaning the fingertips, it is best to wipe it gently with a rag, and it will be clean. When dialing before and after washing, you can directly aim the water pipe at the gap between the front and rear dials to rinse with water, so that the mud and sand stuck in the front and rear dials can be washed away. After flushing, you can also use detergent to wash off the oil on the front and back dials.

4. Fork, pedal, brake

It's easy to clean the front fork and pedals. The pedals only need to be washed off with mud. It is best not to rinse the front fork with water. When scrubbing the inner tube of the front fork, wring out the water on the rag before wiping. Some impurities will remain on the inner tube of the front fork after using it for a period of time. You can gently wipe it off with a cotton swab. It is best to develop a habit of keeping the front fork clean. This is also the most basic maintenance of the front fork. When washing the brake (subject to the V brake), you can directly flush the mud and sand left in the brake with a water pipe to prepare for the next maintenance.

For roulette, front and rear transmission, guide wheels, etc., dust and small dirt can be removed with a brush.

5. Crankset, flywheel and chain

In the entire cleaning process, these three accessories may be the dirtiest parts. Because the lubricating oil is left on the accessories, dust is most likely to adhere. We can pour the same dishwashing detergent on the cloth first, and then clean the tooth plate after dipping it in water. When washing the tooth plate, try to wash every tooth with a cloth as much as possible. After washing, rinse with water. You will be pleasantly surprised to find that the crankshaft is as bright as new under the scrubbing with a dishcloth.

The next thing to wash is the flywheel. To wash the flywheel, remove the rear wheel for cleaning. First release the rear brake so that the brake does not pinch the wheel. First, loosen the screws on both sides of the rear wheel quick release. At this time, tap the rear wheel lightly and the wheel will come out.

Put the wheels on the ground, wipe them carefully on the flywheel with a rag, pay attention to the position of the rear derailleur when putting the wheels back on the bicycle, slowly pull the rear derailleur to put the wheels in. This process is very simple, and you can understand it after disassembly and assembly once or twice.

The last thing to be cleaned is the chain. After a long period of riding, a lot of sand will stick to the chain. There are many ways to wash the chain. The author introduces two methods here: The first is to wash the chain with kerosene, and drag the chain back and forth with a rag with kerosene. The disadvantage is that it will leave you with a peculiar smell, grease and oil stains. The second method is to use dish soap. It should be noted that when washing the chain, it is best to use hot water of about 45 degrees, this temperature is easier to play its cleaning effect. In addition to the need to wipe the chain back and forth with a rag with detergent, it is best to use a thicker brush to slowly brush each link of the chain once, and the black chain will soon show the original color.

Comments

Leave a comment

All blog comments are checked prior to publishing